Simple Solutions for Addressing Common Refrigerator Repair Issues

Is your refrigerator running? What used to be a common prank quickly loses its humor when your refrigerator malfunctions. If your refrigerator isn’t performing up to its usual standards, it’s important to act quickly to prevent any issues from becoming larger problems. While some refrigeration issues may require the attention of a trained professional, there are many refrigerator repairs that you can complete easily at home with some basic troubleshooting and minor adjustments.

Here are some common symptoms requiring refrigerator repair samsung refrigerator repair pasadena, along with steps you can take toward resolving them:

Temperature Instability: If your refrigerator is warm, or if it is too cold and is freezing your food, the first thing to check is the internal temperature control dial. If adjusting the temperature setting doesn’t resolve the issue, check the condenser coils, located on the back of your refrigerator. Occasionally, these coils can become coated in dust and debris, prohibiting the unit from cooling efficiently. If you continue to experience problems with temperature instability after cleaning the coils, you may need to call a refrigerator repair service to adjust the internal thermostat settings.

Leaking: A leaking refrigerator is a particularly urgent issue, requiring immediate attention to prevent exacerbated problems including water damage to the floor and other surfaces in your home. If you’ve got water on the floor outside of the refrigerator, check the condensing defrost tray underneath the fridge. If the tray is tilted, not level, or damaged, it could allow water to leak out onto the floor. If you’ve got water leaking inside the refrigerator, it may be due to a malfunctioning humidity control. If your refrigerator has an ice/water dispenser, check the water lines for leaks.

Excessive Noise: A certain amount of noise is completely normal for a refrigerator, but excessive groaning, knocking, or banging noises are indicative that something’s wrong. Check to see where the noise is coming from. If you’ve got a banging or rattling noise coming from the back of the refrigerator, you may have a loose compressor or fan. If the sound originates underneath or near the front of the fridge, you may need to loosen the screws that hold the condensing defrost tray. A sputtering noise can be typical of a refrigerator going into defrost mode. If you’re unable to determine the source of the sounds, or if adjusting the loose components doesn’t resolve the issue, you may need to contact your local refrigerator repair service.

Failure to Run: If your refrigerator isn’t running, it may be tied to a power issue. The easiest fix is to check and make sure that the power cord is plugged in, and that your outlet is working properly. If that doesn’t fix the problem, check whether the light inside the refrigerator cabinet is on. If it isn’t, it’s a sign that your refrigerator isn’t receiving power, and indicates a problem with the power cord. If the light is on, however, but the refrigerator won’t cool, it’s likely an issue with the condenser or cold control.
If you’re unable to determine the cause of your refrigerator’s malfunction, or if a minor parts adjustment doesn’t resolve the issue, you may need to contact your local appliance repair service for professional refrigerator repair. Although fixing a problem yourself may save you some money in the short term, refrigerator repairs can be complex, and you don’t want to risk personal injury or property damage due to a faulty amateur repair job. When it doubt, rely on the knowledge and expertise of the pros to restore your refrigerator to proper working order.

Best Ways to Find a Dependable Refrigerator Repair Company

The dawn of the internet has made searching for a refrigerator repair service an easy and convenient. Today, most repair companies already have an online presence. In fact, it has become a necessity for any local business to maintain an online presence because it is by far the cheapest way of advertising.

Just a quick search through Google will give quiet a long list of repair companies available within your area. You can also contact them easily online through email, Facebook or twitter. This doesn’t mean, however, that you will just pick the first name that pops in the search result and arranged a deal in an instant. There are a few considerations you have to look into, if you want to get the best refrigerator repair service kenmore refrigerator repair altadena.

The most important factor to consider in choosing the best refrigerator repair service is the company background. Company background includes business permits and other licenses, accreditation and staff training and certifications. The repair company’s length in service also will be a very important information to know also. It will not only tell of the company’s stability but its dependability as well. Longer years in service would mean that the repair company has loyal patronage and higher customer satisfaction rate.

Another great method of researching for a refrigerator repair company’s background is to check online for performance reviews. Local business directories like Yellow Pages or online forums provide a very good and unbiased feedback for this. You would get interesting insights from these reviews on how good the company is in delivering its promised services. Aside from reviews, word-of-mouth referrals are also undisputed. You could try getting suggestions from your family and trusted friends. They are bound to suggest companies that they think will suit your taste and preferences. And because you know them personally, you can at least guarantee that they would be dead honest in their opinions.

Aside from the company background, it is also important to consider and know the details of the refrigerator repair company’s insurance policies – if they do have one or not. If they do not, then by all means, forget that company and move on to another. If they do offer insurance and warranty, review it thoroughly and make sure that it suits and satisfy your needs. You have to know if you have protection in case they accidentally do more damage to your appliance.

Finally, make it a point to check on the scope of the services that the refrigerator repair service will provide and the price that they will assign to it. Get a price quote before agreeing on any offer, and make sure to scrutinize if things are worth it.

The Tech Sheet For Your Washer, Dryer, Refrigerator,

I’m Don Rowan. I’m back again to give you some more tips. In this article I want to share with you some of the information that the the suppliers and tech’s use to help them figure out how to repair your appliance. First, most appliances have a tech sheet. This tech sheet contains information about the machine for the service repair man. Sometimes it contains the error codes that can sometimes help you figure out what the problem is. If you cant find your tech sheet and are in need of finding a error code, many appliance repair sites contain a list with a manufacture list such as ( Whirlpool, Kenmore, Ect ). An example would be like: A GE oven has a F1 error Code, in many cases this would be a touch panel or main control problem and the tech sheet sometimes will give you a way to figure out witch one is causing the error code. Some of the Microwaves have a flow chart in the tech sheet that will also help in diagnosing a problem with the microwave. If you are working on a side by side refrigerator and are having problems with the ice machine the tech sheet sometimes is located in the bottom kick plate and will have detailed information on how to test your ice machine. You now can see how important a tech sheet can be for the repair person to help repair your appliance maytag washer repair pasadena.

After a tech or repair person figures out what part is causing the problem with your appliance, they might need to find the part number. It might be located on the part and it might not. You will need to find a diagram or breakdown of the machine to locate the part number so it can be purchased. There are a few sites on the internet that will give you this information. They will require a model number and some also require a serial number as well. each of these kinds of sites work a little differently but you will half to have a model number to get a diagram to come up. If your machine is over 10 years old your appliance might not come up on most of these web sites and you will half to find a parts distributor to have it looked up.

Finding the Model #

The manufacturers over the years have placed the model number in many places. I will try to give some ideas of where they might be located for you. Refrigerator: older GE side by sides use to be located near the front bottom near the kick plate. Newer model refrigerators are usually inside the fresh food compartment near the top right side. I have found model numbers for refrigerator in the following places:

Behind crispers, on the ceiling, where the door hinge is (mostly on subzero), on the door, in the compressor compartment (mostly on built in units). If you cant find the model number and you don’t have the part number it will be very difficult to fix your machine. You might get lucky if you know what part is bad and try to have a parts distributor match it up.

Dryer model numbers:

Mostly located on the inner door, door itself, or on the very top of the console.

Washers model numbers:

First check to lid and directly under the lid while its open (this can sometimes be hard to see) and the top of the console. Some older models were on the right or left side of the machine toward the bottom.

Washing Machine Repairs – Faulty Water Heater Element

If your washing machine does not heat the water during its wash cycle, it is likely to need some kind repair, a faulty water heater element is the most likely cause for this type of problem, here are a few checks that you can use that will indicate to you whether you have a likely faulty water heater element.

There are a few ways to tell if the water heater element in your washing machine might not be working and only one way to know for sure, I will go over some of the ways you can use to tell if your washing machine water heater element might not be working and also explain the 1 method you can use to to tell for sure if your element has developed a fault or not ge washer repair pasadena.

If your washing machine blows a fuse or circuit breaker within a few minutes of turning it on, this could be many things and would need further testing but one of the things that could be causing the fuse to blow is a faulty water heater element.
If your wash is not coming out as clean as it used to, this again could be a indicator of a faulty element as the clothes could be washing in cold water.
If you touch the glass on multiple occasions throughout the wash and the glass feels cold every time, this again is another indicator of a faulty element as on most washing machines the glass section of the door will become at least warm during the hot wash cycle.
If the wash seems to go on and on and takes much longer than usual and with some machines the wash cycle may even just go on and on until you stop it, this again is a indicator that the element may have a fault, on some washing machine the wash cycle will not stop or move on to the next cycle until a certain preset temperature has been reached, so the machine would just go on and on waiting for the element to heat the water to the preset temperature, but be warned there are other problems that can show very similar symptoms to all the above.
The only sure way to tell if a element is faulty, even if all the above faults are present, is to use whats called a ohmmeter, a ohmmeter is a device used for testing all types of electrical values, including resistance between 2 conductive device. To test if a element is working or not a engineer would connect a ohmmeters live and neutral wires to the corresponding connectors on the element and check for a positive reading, no reading would mean a faulty element, the engineer would also use the ohmmeter to read across both terminals again and the earth terminal on the element but in this case a positive reading would mean a faulty element and a negative reading would mean no fault on the earth to live and earth to neutral connectors
You should be competent with electrics with a degree of experience to do the above test has it involves opening your appliance and removing and replacing wires inside the machine that will become live once the wires are replaced and the washing machine is turned on, there is no “zero” place for mistakes on this job, if you do not fully understand house hold electrics you should not attempt the test.

Do You Really Need a New Washing Machine?

Most people have had their washing machine break down at one point or another and it’s incredibly inconvenient especially if you have little time to spare already!

However, the average person immediately assumes that when their washing machine stops working or leaks water that it has died a watery death and they begin to search for a new model. They then throw out the old one and spend a fortune on replacing it as quickly as possible since washing machines are integral to the smooth functioning of the household. In other words, people rely on it daily lg washer repair pasadena.

Throwing out your appliance is a key mistake unless you are absolutely certain that it is broken. What you want to do is go online and look for washing machine repair services or handymen that are based in your local area. This will save you time and effort. Plus, contrary to popular belief, hiring a local repair man will save you money and in many cases he will be able to fix the problem. Brand new washer dryers typically cost between £300-400 and can be unnecessary if you invest in a professional first.

Before you lose faith in your washing machine and decide to replace it, ask yourself – “Do I really need a new machine?” This question will be happily answered by a local appliance repair man who will have the expertise to advise you in the best way.

Logically, having your washer dryer repaired will greatly outweigh the hassle of shopping for one yourself and waiting for it to be delivered. It will also eliminate the possibility of throwing out a perfectly good washing machine! This is especially important if the washing machine that you own was one of the more prestigious models that usually cost around £800! In this case, it would be wise to seek advice and see if you can repair your machine first. It would be insane to waste this amount of money and yet be oblivious to what caused it. Often it’s a minor problem that can be rectified in a short space of time, allowing you to get on with your life.

It is advisable to remember than if you need your appliances repaired quickly and at a cheaper rate, then avoid some of the bigger branded companies. Sometimes, these companies will charge you an inflated price since they have more outgoing costs. Instead, look for someone local who will charge you a reasonable rate and have a small distance to travel to reach you.

Just having this knowledge will allow you give a more informed reply when asked – “Do you really need a new washing machine?”

Clothes Dryer Vent Cleaning

A clothes dryer needs a little ongoing maintenance to keep it in safe and in proper working condition.

How does a clothes dryer work?

The way a clothes dryer works is pretty simple, it spins clothes around in hot air while an exhaust vent sends damp air outside. An exhaust tube connects to the back of your clothes dryer and then to a duct in the wall that leads somewhere outside, so all the hot, moist air coming out of the dryer ends up outside. As your heated clothes tumble in the hot air, lint comes off the fabric and most of it gets caught in the lint trap as the exhaust air passes through it. The lint trap is usually accessed either inside the dryer door or on top of the dryer and it usually looks like a plastic or wire screen. Whatever gets past the lint trap goes out the exhaust vent and duct and either clings to the sides of the tube or blows out the exhaust vent outside whirlpool dryer repair pasadena.

Clothes dryers blow exhaust air out through ducts, the shorter the ductwork the better. The total recommended length is less than 25 feet from the back of your dryer to the outside vent cover, that’s with a straight running exhaust duct. If you have bends and turns, it should be an even shorter distance. The more turns and the further the distance, the harder your dryer must work to move exhaust air and loose lint. The harder your clothes dryer works and the longer it runs, the sooner it will wear out and have to be replaced or repaired.

If your clothes dryer has clogged vents and ducts, there are usually a few signs you’ll see:
• Loads of clothing will take longer to dry.
• Clothing will be very hot and still damp when the dryer finishes.
• The clothes dryer itself will feel hotter.

A lint-clogged clothes dryer can often consume 15 – 25 dollars worth of extra electricity every month trying to dry your clothes, so it makes good sense to keep your dryer vent and it’s ductwork clean.

So what kind of maintenance do you need to do for your clothes dryer?
Lint tends to build up in 3 areas:
1. Inside the lint trap.
2. Inside the flexible duct hose behind the dryer.
3. Inside the in-wall duct work, leading to the outside vent flap.

Step one is to clean the lint trap after every load of laundry. How do you clean the lint trap? You pull out the lint trap and scrape out the lint with your fingers or bang it over the trash can to clear it out, and then replace it. When you pull out the lint trap, look around inside the dryer in the pocket where it sat, if you see more loose lint there, take it out (you can use your hand, a brush, or your vacuum). By doing this simple cleaning regularly, you will avoid 90% of clothes dryer vent problems.

Home Appliances: Rules For Repairing

Appliances are imperative for everyday life. These machines can be small or major and are found predominantly in the kitchen. Known as brown or white goods, there are a variety of electrical and mechanical appliances for the home.

These appliances tend to be found in your kitchen, and are things like: fridges, freezers, washing machines, kettles and toasters.

They are built to perform and appliances need to keep going year on year Appliance Repair Van Nuys. Because they often come without problems it’s easy for people to take them for granted and thus when an appliance breaks down, many people are at a loss as to why this has happened and how to fix it.

Generally, you need to get some professional help but there are always people who try their hand at these types of things. Before you pick up a tool and go at it yourself, there are many things you need to know about home appliances.

Nearly all appliances use the electrical system in your home and are usually labelled so you know the power requirements. Fixing these appliances can be simple or complex but, in either case, you need to know how to diagnose the problem before you can fix it.

You need to figure out the malfunctioning part by isolating the failure. Whilst it is always advised to get a professional to fix home appliances, you should at least take note of these three key ideas for repairing appliances:

Disconnect the appliance – When going to diagnose, or try to repair, your appliance, ensure that the gas or electricity supply is disconnected. Any adjustments should be done with the power turned off.

What are they built with? Are you trying to fix a part that is held together with plugs, bolts, screws and fasteners? Then you can probably try to fix it yourself.

Repair or replace? There can sometimes be a judgement call as to whether it is more financially prudent to repair the home appliance or simply replace it. You can often get the new parts ready-made.

Always make sure that you consult the manuals of your appliances before doing any work on them. Sometimes though, a problem with equipment could be as simple as a lack of power – that is the most common reason for appliance failure.

Always check that your cord is properly plugged in and everything is working properly. You can do this with a voltage tester while you are also double checking that fuses and circuit breakers are working and not tripped or blown.

Don’t Let Your Home Systems Underperform – Call a Heating, Cooling, or Appliance Repair Expert Today

Home appliances–from stoves to hot water heaters–malfunction from time to time, causing us to lose energy and money and posing a potential a safety hazard. That’s why it’s important to get a professional repair expert on the job immediately when you notice a problem.

It can be tempting to make do with a malfunctioning appliance–a dishwasher that doesn’t get the dishes all the way clean every time or a furnace that clanks a bit doesn’t seem like the end of the world, after all. And who whats to spend money to fix something when there doesn’t really seem to be a problem? The truth is, though, we don’t always know what symptoms like this mean. They could be innocuous or they could herald a more serious issue. A trained appliance service professional will be able to tell you what a malfunction or strange noise actually means. With their help, you can make sure that an appliance that’s on the fritz isn’t draining more energy than it should be and isn’t endangering the safety of you or your family Jennair Appliance Repair Los Angeles.

Major heating and cooling appliances such as water heaters or large air conditioning units use a lot of energy even when they’re in peak condition. If something internally isn’t quite right, though, that means that the machine has to work harder to do the same work. Consequently, it’s going to be extremely energy inefficient. The same is true of smaller appliances as well. In either case, your utility bills may not show a huge spike immediately, but, over time, excess power consumption will increase your overall energy costs. Whether you need air conditioning service or a refrigerator repair to get things back on track, an appliance expert will be able to help. These professionals will find out what’s wrong and perform the necessary work to get your appliances up and running again in top condition–and using exactly the amount of energy that they should be.

Unfortunately, energy bills aren’t the only thing to be scared of when it comes to appliances that aren’t working properly. Incorrectly functioning machines also pose a health and safety risk to everyone in their vicinity. If you need a stove or dryer repair, for example, those appliances can pose a potential fire hazard until that repair is taken care of. Appliances connected to gas lines bring in a whole new level of danger. A damaged or broken gas-powered appliance makes a gas leak a frighteningly real possibility. This is why it’s so important to have a professional check out the machine. Whether your situation calls for an oven or furnace repair, call an appliance expert immediately so you can rest easy knowing that there’s no danger to you or your family from a faulty appliance.

Appliance repair isn’t just a matter of dealing with the inconvenience caused by a machine that’s not working right. It’s also about saving you money in energy costs and making sure that the malfunctioning appliance doesn’t pose any kind of threat to the people who are trying to use it. If you need anything from a water heater fix to a washer repair, call your local appliance or heating and cooling specialist today to take care of the issue right away.

Washing Machines and Principles of Operation

Soil removal in a modern washing machine is a combination of chemical and mechanical processes.

1. Chemical action. The detergent or soap solution dissolves and loosens the soil in the fabric.
2. Mechanical action. Flexing the clothes and forcing the detergent or soap through removes the soil. The functioning of the washer is aided by the heat and softness of the water, which increases the chemical action of the detergent or soap used.

Almost all modern automatic washers employ one of two types of mechanical action, tumbler or agitator. The latter is by far the more popular and more commonly used. But all automatic washers, regardless of type, model, or make, have only four basic functions of operation: (1) fill, (2) wash, (3) pump out, and (4) extraction (spin) Washer Repair Los Angeles.

The heart of the agitator-type washing machine is the agitator, which usually consists of vanes or blades on a cone that fits over a central shaft in the washer tub. As the agitator turns back and forth, the blades or vanes catches clothes and move them about. This movement also creates currents in the water, which contribute to the cleaning action.

There are almost as many agitator designs as there are washers that use agitators. Agitators have vanes or blades of various numbers, designs, and sizes, which are arranged in a vertical or spiral position. Agitators may be of solid or perforated plastic or metal (usually aluminum).

Most agitator-type washing machines employ an oscillating (back-and-forth) action during the wash cycle. To produce this oscillating action, the arm is generally connected off-center to a low-speed gear wheel. As this gear wheel turns, it imparts a back-and-forth motion to the arm. This motion, in turn, is transmitted to a pinion gear which drives the agitator.

There are also other methods of driving the agitator. For instance, a few models provide a slow-speed, off center, wobbling motion to the agitator, while some others impart an up-and-down, pulsating motion to it. While the oscillating action is the one most commonly used for the washing operation, some machines of this type employ a rotating or revolving motion to spin the tub or basket for the extraction operation. To accomplish this, a clutch action of some type is used to disengage one set of gears and engage the other. One such clutch used in washers consists of a pin dropping in place in a hole in the drive gear to engage it or it may be a friction type, as is frequently found in automobiles. Incidentally, agitator-type washing machines are top loading, meaning that the clothes are placed in the washer through a door or lid that opens on the top of the unit.

The front-load type of automatic washer has gained in popularity in recent years. The tumbler mechanism is a perforated cylinder, usually aluminum or porcelain-enameled steel, which holds the clothes; it revolves in a larger tub that holds the water. Within the cylinder are baffles, which are projections designed to carry the clothes along, through, and out of the water, until the position of the clothes causes them to fall downward again, and the process is repeated.

The axis of rotation of the washing cylinder usually is either parallel to the floor or inclined upward from the floor at approximately a 30 degree angle. A few have a vertical cylinder. Most tumbler-type washers are loaded from the front, but some can be loaded from the top or at an angle. During the washing cycle, the cylinder revolves slowly, tumbling the clothes about in soapy water. During the damp-dry cycle, the cylinder revolves rapidly, and centrifugal action helps to throw the water out of the clothes. The low speed for washing and the high speed for damp-drying are provided by the gears in a transmission as in an automobile. In a similar manner, there is a gear-shifting arrangement and a clutch to engage the gears.

The needs and components of both tumbler and agitator washers are about the same. For example, both require hot and cold water. This water is fed into valves in the washer which turn on and off the hot and cold water and mix them at appropriate times. While a few washers control water temperature with a thermostat, most operate on a simple on-off principle. When the hot water is on and cold is off, the water in the washer is hot-whatever temperature the water-heater tank provides. When the cold water is on and whatever temperature the cold-water tap provides. When both hot and cold are on, they are evenly mixed to provide warm water; with average cold water temperatures out of the tap (about 50F), the mixture comes out at about 100F.

FAQ About Cleaning and Repairing Dryer

If you haven’t had your dryer vent cleaned recently, you may want to rectify the situation as a clogged duct is a hazard to you and your family. This matter can be fixed if you hire an expert to rectify the issue. Here are some of the most common questions about this type of cleaning and repairs:

How often should my dryer vent be cleaned?
You should have a thorough cleaning done at least every two years. Factors determining this include the length of the vent, how many turns it has and how often the dryer is used. A dryer with a short vent and is used little may be able to go without cleaning longer than normal, while those who use the appliance on a regular basis might need a yearly cleaning Dryer Repair Los Angeles.

Why should I get my dryer vent cleaned?
Cleaning it lifts a huge safety risk that weighs on you and your family. Dryer fires are usually the cause of a dirty or improperly installed vent. Another risk from dirty vents is carbon monoxide gas buildup.

A proper cleaning will save you on the cost of electric or gas. A spotless pipe will allow the appliance to move the proper amount of air through the system, allowing your clothes to dry at a faster rate without using extra power.

How will I know it’s time for a cleaning?
Your dryer will leave a few tell tale signs. If you notice a significant change in drying times, if you can’t feel air blowing from the vent outside from at least a foot or if you see lots of lint starting to collect, then you need to get it cleaned.

Is there a difference between vinyl and metal hoses?
Aluminum hoses have a much higher temperature range, and they do not deteriorate like vinyl hoses. Maybe most importantly, aluminum hoses are also fireproof.

Is a longer hose better than a short one?
A shorter run is more efficient, as it doesn’t clog up as fast with lint and costs less to clean, while a longer hose run will have your dryer working harder.

How should I protect my dryer vent from intrusion?
There are covers available for purchase. One of the most common ways is to cover it with mesh, but this creates a fire hazard, so experts don’t recommended you do this.

My dryer smells like smoke whenever I turn it on.
The lint is probably getting trapped behind the dryer tumbler, and this is because your hose is jammed with lint or other debris. The lint gets trapped on the tumbler and the heating element dries it out, causing it to catch fire. Have your vent cleaned immediately.

Why is my hose collecting water?
Most likely because the hose has a sag. This sag is causing condensation to collect more water over time. Water will lead to rust and sludge, so have it fixed ASAP.

Should I remove the back of the dryer to clean the vent?
You should really call a professional to have your vent cleaned. It is not recommended you remove the back of the dryer.

Can I vent my dryer to the basement?
You should never vent it to an indoor space, as the heat and moisture will result in mold growth. Always have your dryer vented outside.